Join our mailing list!



Knowledge Base:  

You are here: Knowledge Base : 4 axis
Page of 3
JR Series 4 Axis Adhesive Dispensing Robot
TS250 dispenser training guide and setting up
A New Dimension to Bench-top Fluid Dispensing P RODUCTIVITY-ENHANCING DIGITAL DISPENSERS/ CONTROLLERS FROM ADHESIVE DISPENSING LTD T S 2 5 0 Seri
Epoxy Definition
Epoxy - Available in two-part or one-part, both room temperature and heat curable formulations, epoxy adhesives provide high strength bonds on a wide variety of substrates. The bond can often t
How to connect dispenser to external source using I/O Configuration
I/O connection guide for TS250, TS255, TS350 and TS355 dispensers/ controllers. I/O Configuration and End of Cycle Switch Upon completion of a dispense cycle, an open collector circuit closes and rem
TS250 and TS350 dispenser I/O Configuration and End of Cycle Switch
TS250, TS255, TS350, TS355 I/O Configuration and End of Cycle Switch Upon completion of a dispense cycle, an open collector circuit closes and remains closed until the next dispense cycle. This circu
Benchtop dispensing robots
Information guide Benchtop Robots Benchtop robots have been a useful asset and have aided the assembly process since the early 1990s. Th
Fisnar part numbers and part codes
Fisnar part numbers and part codes Part # Description 0603-20140003 Tp Tip Holder Silver 0603-2020017 F7300N Robot Z-Axis Cover 0603-20210007 Dispenser
Dilatent Definition
Dilatent - A liquid where viscosity (thickness) increases with shearing rate (when you stir it). Dilatent is the opposite of Thixatropic.
70303RHB Adapter Assembly 3cc Size 3ft Long
USE THIS ADAPTER ASSEMBLY AS THE AIR LINK BETWEEN THE PNEUMATIC DISPENSER AND 3CC SIZE BARRELS Product Description 70303RHB is an air adapter assembly for 3cc/ml siz
Accelerator Definition
Accelerator - A fluid used to speed up material curing Usually a low viscosity single part liquid. Sometimes supplied as an aerosol, in a can or in a bottle with a brush.
Acrylic Definition
Acrylic - A structural adhesive capable of bonding a broad range of substrates including most types of plastics and metals both minimally prepared and unprepared. Two-part catalyst cure or one
Anaerobic Definition
Anaerobic - A one-part adhesive/sealant that cures only in the absence of air. Designed for locking screws, nuts, bolts and/or retaining bearings, shafts, etc. A single part adhesive. Supplied
Aqueous Definition
Aqueous - Meaning water based fluid or containing water. Common glues including PVA, wood or paper glue. Easily dispensed with manual or air-powered dispensers.
Braze Paste Definition
Braze Paste - A paste or flux material. For alloys that melt above 425 deg c. Easily applied using air-powered syringe dispenser.
Caulk Definition
Caulk - Uusally a sealant or silicone used to fill gaps as well as describing the process of gap filling.
Conductive Epoxy Definition
Conductive Epoxy - A term used with fluids that will conduct electricity. These materials often come pre-packed in dispensing barrels or cartridges.
Cyanoacrylate Definition
Cyanoacrylate - A one-part adhesive that cures instantly on contact with mated surfaces. High strength, excellent adhesion to a wide variety of substrates. Cyanoacrylates are available in a var
Hot Melt Definition
Hot Melt - A thermoplastic material that is melted in dispensing equipment and is applied in a molten state. It then wets the substrate surface and as it cools, it solidifies forming a bond. Ve
Polyurethane Definition
Polyurethane - One or two-part urethane adhesives provide superior bonds with minimal surface preparation for today's high performance thermo sets and thermoplastics. They provide excellent fle
Silicone Definition
Silicone - One-component adhesive/sealant that cures to a tough rubbery solid upon exposure to moisture in the air. Silicone has good resistance to weathering, vibration, moisture and chemicals