Join our mailing list!




  Home >

Low Viscosity Potting Epoxy Black 50ml pk/5
ADPX771FF Black Potting Epoxy 50ml
ADPX771FF low viscosity potting


 
Price: £125.00 Exc VAT

Stock Status:(Out of Stock)

Availability:: 1-2 Weeks
Product Code: ADPX771FF
Qty:

Description Technical Specs More Information
 
ADPX771FF is a two-part semi-rigid Epoxy Adhesive, room temperature curing adhesive designed for the impregnating and bonding of dissimilar materials and black in colour. 48 hours at 10 C, 24 hours at 20 C, 12 hours at 30 C is cure time.
High adhesion
Non-toxic
Thixotropic
High impact resistance
Fast curing (Incomplete mixing will be characterised by variable or partial cure).

Specifications:
Colour : Black
Specific Gravity g/ml: 1.1
Viscosity m.Pa.s @ 25 C: 6,000
Mix Ratio by Volume: 1: 1
Working Life (10g @ 25 C): 15 minutes
Gel Time (10g @ 25 C): 30 minutes

Cure Schedule Typical Properties:
Initial Cure: 90 minutes @ 10 C, 60 minutes @ 20 C 30 minutes @ 30 C
Full Cure: 48 hours @ 10 C, 24 hours @ 20 C, 12 hours @ 30 C
The above are typical values and will vary depending on the cured mass and application. Hotter temperatures may be used for faster cure but will result in higher post cure shrinkage and higher cure exotherm. Experimentation and testing is suggested to avoid side effects. For maximum properties a post cure may be required.
Typical Properties:
Shore D Hardness 75
Operating Temperature -40 C to +120 C (Application and geometry dependant)
Thermal Conductivity 0.3 W/mK
Tensile Strength 18 mPa
Elongation at Break 5%
Compressive Yield Strength 15 MPa
Coefficient of Linear Expansion 70 - 90 ppm/C
Volume Resistivity 13 Log10ohmm
Electric Strength 15 kV/mm

Lap Shear Strength:
Aluminium : 17 Kg/cm2
Stainless Steel : 15 Kg/cm2

Kits: In kit form, resin and hardener are provided in separate containers to the correct ratio. In most cases, pour the hardener into the larger resin container and use it as a mixing vessel. Stir well using an appropriate mixer until homogeneous.
Cleaning: All equipment contaminated with mixed material should be cleaned before the material has hardened. TS130 is suitable nonflammable cleaning agent, although other solvents may be found suitable. TS130 will also remove cured material provided it is allowed to soak for a number of hours.
Storage and Shelf Life: Material stored in the original unopened containers under cool dry condition between 10 and 35�C will have a shelf life of at least two years. Once used the containers must be kept sealed to prevent effects from water, air or contaminants.
Health and Safety: Epoxy resin systems may cause sensitisation by skin contact or inhalation may be corrosive, harmful or toxic. It is therefore strongly recommended that skin and eye contact is avoided by the using of appropriate personal protective equipment such as gloves, safety glasses or goggles and overalls. Wash any contamination from the skin immediately and thoroughly and do not eat, smoke or drink in the working vicinity. Under normal working conditions a good source of ventilation is adequate, however if the material is heated then local exhaust ventilation (LEV) may be required especially for curing ovens.
Adhesive Dispensing Ltd provide a wide range of equipment options for dispensing almost all assembly fluids - from watery liquids, solvents, primers and activators through to thick pastes, sealants, silicones, gels and epoxies.
Features
  • Fast curing
  • General purpose
  • Low shrinkage Pots a wide variety of materials
  • Tough and resilient

Related products...
50ml Pneumatic Dual Gun 1:1 ADCBA-25D
Price: £125.00 Exc VAT

Add
Pneumatic 50ml 1:1 Ratio Gun Part ADCBA-25D
50ml Manual Dual Gun 1:1/ 2:1 ABM-25M1
Price: £14.50 Exc VAT

Add
ABM-25M1 manual cartridge gun 50ml 1:1/2:1 Ratio
Mix Nozzle 5.4mm ID x 17 EL MAH 05-17S pk/100
Price: £50.00 Exc VAT

Add
MA5.4-17S Static Mixer Nozzle