 |
 |
 |
|
The AD5622 dispense valve accurately control the application of most low to medium viscosity fluids without drips. The unique seal-less design incorporates an inert polymer diaphragm that isolates the actuator from the valve. The adjustable open/ close stroke 0.13 to 0.64 mm (0.005 Inch to 0.025 Inch) allows for a very fast response with positive shutoff. Wetted components are made of inert materials.
This version has Teflon wetted fluid housing and diaphragm. Valve open time can be as short as 15 milliseconds. Deposit rate can be as high as 500 shots per minute.
This valve takes a direct feed from any pressure pot, cartridge or syringe and includes a selection of flexible fluid line tubing and connectors. The compact design allows for easy installation in most areas or it can be bench mounted for hands free operator control.
A typical setup for this valve usually includes a digital controller and small pressure pot.
Model AD5622VT with Teflon polymer wetted parts is used for dispensing solvents, cyanoacrylates, anaerobics and fluxes. This valve is very simple to operate using a pneumatic dispenser/ controller. Supplied with air hose, input fittings, tip adapter, mounting bracket, tip selection and user guide.
Part ID: AD5622VT (TS5622VA)
Wetted Materials: Teflon, UHMW
Size: 76mm L x 28mm Diameter
Weight: 118g (0.26lb)
Viscosity Range: 1 - 50,000 CPS
Repeatability: +/- 0.30%
Cycle Rate: Up to 500 Cycles/ Minute
Flow Rate (Water): 5250ml/minute @ 70 psi
Min Shot Size: 0.0075 cc/ ml
Max Fluid Pressure: 70 psi ( 5 Bar)
Activation Pressure: 70 psi (4.8 bar) minimum
Material Inlet: 1/8 Inch NPT
Material Outlet: M5
Mounting: 10-32 Inch UNF
Warranty: 1 Year
Commodity Code: 84248940
Brand: Adhesive Dispensing Ltd
Adhesive
Dispensing Ltd provide a wide range of equipment options for dispensing
almost all assembly fluids - from watery liquids, solvents, primers and
activators through to thick pastes, sealants, silicones, gels and
epoxies.
- Part ID: AD5622VT
- Wetted Materials: Teflon Size: 76mm L x 28mm Dia..
- Weight: 118g (0.26lb)
- Viscosity Range: 1 to 50,000 CPS
- Repeatability: +/-0.30%
- Cycle Rate: Up to 500 cycles/ minute
- Flow Rate (water): 5250ml/minute @ 70 psi
- Min Shot Size: 0.0075 cc/ ml
- Max Fluid Pressure: 70 psi ( 5 Bar)
- Activation Pressure: 70 psi (4.8 bar) minimum
- Material Inlet: 1/8 Inch NPT
- Material Outlet: M5
- Mounting: 10-32 UNF
- Warranty: 1 Year
The AD5600 series require little maintenance other than the replacement of the fluid lines, input fittings and tips.
Typical Applications
Diaphragm valves are used for many varied assembly and production processes where controlled deposits of low to medium viscosity liquids need to be applied. Common applications include:-
Dots and beads of Cyanoacrylates
Dots and beads of solvents
Dots and beads of UV cure
Dots and beads of PVA glues
Deposits of liquid fluxes
Dots and beads of threadlockers
General adhesive application
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Ideal for cyanoacrylates, primers and anaerobics
- High precision solution supplied complete
- Repeat dots, lines or potting of most liquids
- Adjustable stroke control for fine tuning of flow
- Syringe feed, cartridge feed or pressure pot
- Supplied with fluid lines and tip kit
- Easy bench mount, machine mount or robot mount
- Simple to control using TS500R, TS250 or TS350
|
|
|
|
|
|
|
|
|
